News and Updates

Single Acting vs Double Acting Cylinder: Which One Do You Need?

October 10

If you are buying a pneumatic cylinder for the first time, or replacing one on a machine you did not build, you will hit this question quickly: single acting or double acting? The two look almost the same on a shelf. They behave very differently once air is connected, and picking the wrong one means either a machine that does not return properly or an air bill higher than it needs to be.

This guide explains how each type works, where each one makes sense, and what to check before you order. It is written for plant engineers, maintenance teams and machine builders, but you do not need a pneumatics background to follow it.

The short answer

If you only need the cylinder to push (or pull) in one direction and something else can bring it back, a single acting cylinder is usually enough. If you need controlled movement in both directions, or you want the return stroke to do real work, you want a double acting cylinder.

The longer answer depends on force, stroke, air supply and what should happen if the air fails. The sections below go through each.

How a single acting cylinder works

A single acting cylinder has one air port. Compressed air enters that port and moves the piston in one direction. When the air supply is shut off, a spring or an outside force, such as the weight of a load, moves the piston back [1][3].

Two layouts are common. In a push type, air pressure drives the rod out. In a pull type, air pressure draws it in [2][3].

Because the spring brings the piston home on its own, a single acting cylinder returns to its starting position even if air pressure is lost. Two of the sources I read describe this as a safety benefit [1][2].

Typical jobs include clamping a workpiece while it is cut or drilled, pushing finished parts out of a mold or off a conveyor, and lifting loads such as vehicle jacks [1][2].

How a double acting cylinder works

A double acting cylinder has a port at each end. Air going into one port extends the rod, and air going into the other retracts it, so the cylinder is powered in both directions and needs no spring [2][3]. A valve decides which port gets the air [1].

That makes it the better fit for anything that must move out and back under control, such as opening and closing a gate [3]. Typical uses include robot arms, conveyors and lifting equipment, and machine tools such as lathes and milling machines [1][2].

One guide puts double acting cylinders at roughly 95% of the cylinders found in pneumatic control circuits [3]. That figure comes from a single supplier’s guide, so treat it as a rough indication and not a measured statistic.

Side by side

Single acting

Double acting

Air ports

One

Two

Return stroke

Spring or external force

Compressed air

Cost

Usually lower for one-way work [2]

Often higher [1][2]

Air use

One guide says about half that of an equivalent double acting cylinder [3]

Higher [1][2]

Control and precision

Lower [1][2]

Higher [1][2]

If air is lost

Spring returns the piston [1][2]

No spring to do this [1]

Size options

Limited by spring size and force [3]

Wider range of bore and stroke [2][3]

What the spring costs you

The spring is what makes a single acting cylinder simple, but it comes with trade-offs worth knowing about.

First, the spring pushes against the piston, so it reduces the force you get on the working stroke [2][3]. Second, the spring takes up room inside the cylinder, which is one reason bore and stroke options are narrower [2][3]. Third, springs wear. Over time the spring’s performance can drift, and the end-of-stroke position becomes less consistent [2][3].

There is also a point about contamination. One guide notes that the spring side of a single acting cylinder vents to atmosphere, which lets dirt in and can shorten service life [3]. If your machine sits in a dusty or humid area, keep this in mind.

Maintenance advice is not completely consistent between sources. One supplier says single acting cylinders need more maintenance [2], while another says double acting cylinders are more reliable because they have no spring return mechanism [1]. In practice, a spring is one more part that can fail, so it is reasonable to plan for checking it.

What double acting costs you

Double acting cylinders use more compressed air, since air fills both sides of the piston [1][2]. Compressed air is not free, and across a plant with many cylinders the difference can add up.

There are two limits to be aware of. One guide says a double acting cylinder cannot reliably hold a mid-stroke position without extra mechanisms, and that long strokes need proper rod guiding [3]. Another describes using a 5/3-way valve to hold the piston at intermediate positions [1]. The two are not strictly contradictory: holding a position with air alone depends on the valve, the load and the leakage in the circuit, so if your design relies on it, test it on the actual machine.

The force is not the same in both directions

This catches people out with double acting cylinders. The rod takes up space on one side of the piston, so there is less area for the air to push on during retraction.

The standard formulas are: extension force equals pressure times piston area times an efficiency factor, and retraction force uses the ring-shaped area left after subtracting the rod [4].

Here is the worked example from a calculator site, using a 63 mm bore, a 20 mm rod, 6 bar pressure and an efficiency of 0.90. Extension comes out at about 1,683 N and retraction at about 1,513 N [4]. The pull is a little weaker than the push, and the gap grows as the rod gets thicker relative to the bore.

The same source gives no formula for spring-return single acting cylinders [4], and I have not invented one. For a single acting cylinder, the spring force is a published figure on the manufacturer’s datasheet, so use that when you size it.

When a single acting cylinder is the right call

Choose single acting when:

  • Force is only needed in one direction, and a spring, gravity or the load can return the piston [3].
  • The job is light: clamping, positioning, marking, light assembly, or simple push and lift tasks [3].
  • You want the cylinder to go back to a known position if air pressure drops [1][2].
  • Air consumption matters and the application is simple enough to allow it [1][3].

When a double acting cylinder is the right call

Choose double acting when:

  • You need powered movement both ways, or a consistent and repeatable cycle [3].
  • The stroke is long, or you need a larger bore than a spring-return design offers [2][3].
  • The return stroke carries a load, like pulling a part back against resistance.
  • You want a cylinder that follows common ISO designs. Two sources say ISO standards are generally based on the double acting design [2][3].

Questions to answer before you order

Whichever type you lean towards, these are the points to settle first. They match the selection factors listed on our own cylinder page and in the supplier guide I used [3][5]:

  1. Force needed. Work out the load and add a margin. Remember that retraction force is lower on a double acting cylinder.
  2. Stroke length. Spring-return designs limit how long the stroke can be [3].
  3. Air pressure available. Check what your compressor and regulators actually deliver at the machine.
  4. Mounting and space. A spring takes up room, and a compact body might be the deciding factor.
  5. Environment. Dust, moisture and temperature, plus how often the cylinder cycles.
  6. Cushioning and speed. Both are on the selection list in our cylinder page [5], so decide how fast the cylinder needs to move and whether you need cushioning at the end of the stroke.
  7. Failure behaviour. Decide what you want to happen if the air supply fails.

Where Airmax fits

Airmax Pneumatics Ltd has been making pneumatic products in Ahmedabad since 1992. Our pneumatic cylinder range covers single acting and double acting types, in standard, compact, magnetic, round body, heavy duty and custom builds. Barrel and body options include aluminium, stainless steel and mild steel with a honed, hard chrome plated bore. The range as a whole is listed with bores from 12 mm to 500 mm and strokes from 10 mm to 2000 mm [5]. Those are range-wide figures, so check the datasheet for the exact model you want.

A few places to start looking:

A cylinder only performs as well as the air supply behind it. You will also need a directional control valve to direct the air, FRL units to clean and regulate it, and the right fittings and accessories to connect everything.

If you want a deeper look at the double acting design, read our post on how a double acting pneumatic cylinder works. If you are also deciding between air and oil, see our pneumatic vs hydraulic comparison. And once the cylinder is installed, our preventive maintenance checklist will help you keep it running.

Still not sure?

Send us the application details: load, stroke, available pressure, mounting and environment. Our team can help you narrow it down. You can contact us here or download the product catalogue.

References

  1. Tameson. “Single Acting vs Double Acting Pneumatic Cylinder.” https://tameson.com/pages/single-acting-double-acting-pneumatic-cylinder
  2. Rowse Pneumatics. “Single Acting vs Double Acting Pneumatic Cylinders.” https://www.rowse-pneumatics.co.uk/blog/post/single-acting-vs-double-acting-pneumatic-cylinders
  3. MCE Automation. “Single-Acting vs Double-Acting Pneumatic Cylinders: Key Differences.” https://mceautomation.com/resources/fluid-power/find-your-fit-single-acting-cylinders-vs-double-acting-pneumatic-cylinders
  4. RedCrab Software. “Pneumatic Cylinder Calculator.” https://www.redcrab-software.com/en/Calculator/Physics/Pneumatic-Cylinder
  5. Airmax Pneumatics Ltd. “Pneumatic Cylinder.” https://www.airmaxindia.com/products/pneumatic-cylinder/